|
|
|
Who's Online
There currently are 5670 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
;
The manual was exactly what I wanted and I found it nowhere else. Thanks!
;
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Top marks.
John Copeland
Glasgow
Scotland
;
I was so happy that the owner's manual was available. It is well written and helped me to use the radio/CD player/recorder without problems. Thanks for making it available.
Irene Lambert
;
Excellant!!! Very quick and easy....Best $4.99 I have spent in a very long time..
I highly recommend this.
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Problem The power does not turn on. Remedy � Connect the power plug to the wall outlet. � Disconnect the power plug from the outlet, and insert again. � Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically.
10
No sound is output when a function is selected. � Make sure the component is connected correctly (refer to pages 16�27). � Press MUTE on the remote control to turn muting off. � Adjust the MASTER VOLUME. � Press the MONITOR button to turn monitoring off. No image is output when a function is selected. Considerable noise in radio broadcasts. � Make sure the component is connected correctly (refer to pages 19�20). � Select the correct component (use the MULTI CONTROL buttons). � Tune in the correct frequency. � Connect the antenna (refer to pages 21�22). � Route all cables away from the antenna terminals and wires. � Fully extend the FM wire antenna, position for best reception, and secure to a wall. � Connect an outdoor FM antenna (refer to page 22). � Adjust the direction and position for best reception. � Connect an additional internal or external AM antenna (refer to pages 21�22). � Turn off the equipment causing the noise or move it away from the receiver. � Place the antenna farther away from the equipment causing the noise. � Connect an outdoor antenna (refer to page 22). � Refer to Speaker setting on page 48 to check the speaker settings. � Refer to Setting the relative volume level of each channel on page 54 to check the speaker levels. � Connect the speakers properly (refer to pages 23�24). � Move the cassette deck further from your receiver, until the noise disappears.
Broadcast stations cannot be selected automatically. No sound from surround or center speakers.
Noise during playback of a cassette deck.
Sound is produced from other components, but � Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG according to the type not from LD or DVD player. of connections made. (refer to page 39). � Set the digital input settings correctly (refer to page 53). � Make digital connections (refer to page 17) and set the SIGNAL SELECT to DIGITAL (refer to page 39). � Refer to the instruction manual supplied with the DVD player. No sound is output or a noise is output when software with DTS is played back. When a search is performed by a DTS compatible CD player during playback, noise is output. Can�t operate the remote control. � Set the digital volume level of the player to full, or to the neutral position. � Refer to the manual supplied with the DVD player. � This is not a malfunction, but be sure to turn the volume down to prevent the output of loud noise from your speakers. � Replace the batteries (refer to page 8). � Operate within 7 m, 30° of the remote sensor on the front panel (refer to page 8). � Remove the obstacle or operate from another position. � Avoid exposing the remote sensor on the front panel to direct light. � Press FL DIMMER on the remote control repeatedly to return to the default.
English Español
The display is dark or off.
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.
75
En
|
|
|
> |
|
