|
|
|
Who's Online
There currently are 5971 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
 ;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
;
Fast service, document is OK. Thanks! Searched for it long time.
;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
Basic Playback
Before operating the amplifier, be sure to press the main power button on the front panel to turn the power ON (_).
Selecting a Sound Mode
To ensure the best possible surround sound, be sure to complete the set up procedures described in "Setting Up for Surround Sound" (starting on page 26) before using the sound modes. This is particularly important when using the 2 (Dolby) Digital or DTS sources. When using the sound modes, SPEAKERS A will give the best results. If you use SPEAKERS B, the sound will be down mixed to the two front B speakers.
Surround operation
1
AMP DVD/LD
DSP
STEREO
EFFECT+/�
1
Press the AMP button.
This sets the remote to select the sound mode. (You can skip this step when using the controls on the amplifier.)
Amplifier
DSP
MAIN STEREO
SUB
REMOTE SETUP MD/TAPE1
2
Select the sound mode.
� For HOME THX CINEMA \ Press THX � For ADVANCED THEATER \ Press ADVANCED THEATER Each press changes the ADVANCED THEATER mode as follows:
TV/SAT
THX MIDNIGHT DIGITAL NR
/ dts ADVANCED STANDARD THEATER
MPEG
EFFECT
CD
VCR1
DIRECT LOUDNESS SIGNAL SELECT
LINE TUNER
VCR2
TV CONTROL
MUSICAL
THX ADVANCED THEATER STANDARD ( MPEG )
DRAMA
5-D THEATER ACTION � For STANDARD \ Press STANDARD ( MPEG ) � For MPEG \ Press STANDARD ( MPEG ) repeatedly.
Each press changes as follows: STANDARD MPEG
� For DSP modes \ Press DSP repeatedly. Each press changes the DSP mode as follows:
HALL1
HALL 2
JAZZ DANCE
THEATER 2 THEATER 1 � For STEREO \ Press STEREO.
Main power button DSP MODE STEREO EFFECT +/�
THX CINEMA ADVANCED
STANDARD ( MPEG )
� The effects of ADVANCED THEATER mode can be adjusted in the range of 10 to 90 by pressing EFFECT +/� (The default setting is 70). Also, the effect level can be set in each ADVANCED THEATER mode by pressing the EFFECT(+/�) button. 5-D THEATER modes cannot be changed. � The amount of effect of each DSP mode can be adjusted in the range of 10 to 90 (the default setting value is 70) by pressing EFFECT +/�. � When a digital input is selected, using some discs with a huge amount of information may cause the overload indicator to light up. If the overload indicator is lit, the signal may be distorting. To ensure there's no distortion you can switch to the STANDARD mode.
42
En
|
|
|
> |
|
