There are currently no product reviews.
Excellent service manual includes everything is need to repair this radio-caseete, how to disassemble, wiring diagram, all , waiting time until the download was only a few hours. I'm going to buy service manuals from here, are cheap and very good.Thank you.
Good service manual,i saved from scrapping this deck,is now fully functional.Thanks.
Found this to be the manual included with the original packinging, was helpfull but did not give any detailed repair instructions.
Complete service manual, was very helpful in repairing this tapedeck.Thanks.
The service manual was a copy of the original from Wirlpool. The quality was good, all neccecary information was available including the service-codenumbers, so I could order the right part to be replaced for repair.
Downloding was no probem after the payment.
Thanks for the service!
Exploring and using the unit
Placing the SW-200
Placing your SW-200 Powered Subwoofer is very easy. Because the SW-200 (or any subwoofer) is nondirectional (it does not send its soundwaves out in a particular direction), where you place it is not as critical as it is for your left and right speakers. It will sound ï¬ne no matter where you place it in the room. However, here are a few suggestions for getting the most out â¢ Once you settle on a location, be sure to leave yourself some room for minor movements of a few inchesâthis can help ï¬netune the sound in the seating area â¢ If you place the subwoofer near your TV, it may affect the picture colors. If this happens, move the subwoofer away from the TV until the picture returns to normal PHASE on the SW-200 so it works the best with the front (left and right) speakers. Here are our recommendations: â¢ Set the subwooferâs LOW PASS CROSSOVER knob to the â150Hzâ setting â¢ Initially set the subwooferâs VOLUME control to the â11oâclockâ position â¢ After listening to music you are familiar with, adjust the
+ R â + L â
LINE IN VOLUME CONTROL PHASE LOW PASS CROSSOVER
Hz 80 60
L REV NOM R
100 120 50 MIN MAX 150
9 2 8
POWER STANDBY RED
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLICANCE TO RAIN OR MOISTURE
WARNING: SHOCK HAZARDâDO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUEâNE PAS OUVER
of the subwoofer.
120V â 60Hz
NOT SUITABLE FOR IN-WALL MOUNTING
Some suggestions for placement
â¢ For the smoothest match between the subwoofer and the front (left and right) speakers, place the 3 of them in an imaginary straight line with each other â¢ For more deep bass output, place the subwoofer next to a wall â¢ For the deepest bass overall, place the subwoofer in a corner. However, this may yield uneven bass throughout the roomâsome areas may have too much bass, while other areas may not have enough
1 POWER Turns the power on and off 2 AUTO SHUTOFF When both the POWER and AUTO SHUTOFF switches are on, the unit turns on automatically when the input receives a signal, and automatically goes into âstandbyâ mode if it doesnât receive a signal for 7 minutes 3 LOW PASS CROSSOVER ADJUSTMENT Adjusts the balance between the bass from the front speakers and the bass from the subwoofer You can adjust the balance according to the size of the front speakers as follows: Large size Medium size Small size 50 ~ 60 Hz 80 ~ 100 Hz 120 ~ 150 Hz After you set the crossover, you can ï¬ne-tune it for the best match between the subwoofer and your front speakers 4 PHASE Switches the subwooferâs polarity to better match the front speakers 5 VOLUME CONTROL Adjusts the volume level of the subwoofer 6 LINE IN jack (RCA-type) Connects to the SUBWOOFER PRE-AMP OUTPUT jack of an ampliï¬er or receiver 7 FROM AMPLIFIER jacks Connects to the LEFT and RIGHT speaker jacks of an ampliï¬er or receiver 8 TO SPEAKERS jacks Connects to the speaker cables from the front speakers 9 STANDBY indicator light Shows that the subwoofer is in Standby mode when it is red, and in Operating mode when it is green 10 Power cord Connects to a 110 â 120 volt AC power outlet 11 Optional feet If you want to use them, attach the 4 feet (using the 4 screws provided) to the pre-drilled holes on the bottom of the subwoofer
Using the Subwoofer with Kenwoodâs KSS-200 or KSS-500 packages
â¢ When you are setting up the KSS-200 or KSS-500 packages, you should set the LOW PASS CROSSOVER, VOLUME, and
subwooferâs VOLUME control and PHASE switch to achieve the best blend between the sound from the subwoofer and the sound of the front speakers â¢ Although you can enhance overall sound quality with the ampliï¬er or receiverâs tone controls, do not set them to âmaximumâ, because this can cause extreme ampliï¬er distortion (âclippingâ) that can damage speakers