|
Who's Online
There currently are 6010 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Very good quality original datasheet!I like this amazing website!!!!!!
;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
RMD-V3104U Rear Panel
1 2 345
INPUT OPTION
V IN
6
7 89 0 - =
COMB OUT
CONTROL IN
DISPLAY
MVP RS-232C RATE MODE
INPUT
V.FIL ON OFF G ( VBS) ( VBS) (Y/C) (Y)
OPTION B (C) R H/CS V
V IN VBS Y/C VBS Y
C
OUTPUT
AC INLET FUSE 125V 3.15A
V OUT1 VBS G Y B C R VBS G
V OUT2 Y B C R
V OUT3 VBS G Y B C R VBS G
V OUT4 Y B C R
~
1 VBS/ Y/C switch
!
@
#
$
Connects RS-232C cable.
%
6 RS-232C connector
Selects whether the VBS (video signal) or Y/C signals are input to the V IN (Video) input. The factory preset is VBS (video signal).
< RS-232C connector diagram > RS-232C pin layout
13 1
2 V.FIL (Vertical interpolation filter) ON/OFF switch
When the optional variable scan board (RMD-V3020) is installed, use this switch to switch the vertical interpolation filter ON/OFF. Set this switch to ON if the top and bottom of the computer screen image cannot be accommodated entirely by the screen. The factory preset is set to ON.
25
14
3 INPUT switch
Selects whether the V IN (Video) or OPTION input is enlarged into 4 screens. The factory preset is set to V IN. � Always press the reset button after changing the position of this switch.
< RS-232C connection diagram > Use an RS-232C straight cable for connection.
< External computer >
FG TxD RxD RTS CTS DSR SG 1 2 3 4 5 6 7 RS-232C straight cable 1 2 3 4 5 6 7
< MVP unit >
RS-232C IN connector
FG RxD TxD RTSI CTSI DSRI SG
4 Remote control input connector
Connects the display's remote control unit. (Adjustment or changes to the settings of the unit cannot be accomplished with the remote control unit.)
� Pins 4, 5 and 6 are internally shorted.
5 RS-232C switch
When performing adjustments from a computer, use this switch to switch between this unit (MVP) and display (DISPLAY). Pins which are not shown in the diagram are not used.
92
|
|
|
> |
|