|
Who's Online
There currently are 5941 guests and 3 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
9. REGLAGE
9.1 RETOUR AUTOMATIOUE 1. Ins6rer un petit toumevis plat dans I'ouverture du tourne-disques. (voir Fig. 9-1) Tourner la came vers la gauche jusqu'i I'arr�t. 2. Prendre le bras de pick-up et le d6placer lentement vers le pivot central. Lorsque I'aiguille du bras de pick-up atteint une position entre 45 et 35mm du pivot central, le bras ne bougera plus. 3. Ins6rer i nouveau le tournevis dans I'ouverture et toumer lentement la came vers la droite. Le bras de pick-up se d6placera lentement vers le centre. R6gler Ia position de I'aiguille du bras de pick-up i une distance de 32mm du pivot central.
Remarque: Si la distance ne peut pas 6tre regl6e d 32mm, c'est que la plaque du bras de pich-up (B) n'est pas en position conecte. Rdinstaller la plaque de l'eraemble de bros de pich-up, et refaire le rdglage de la distance.
Tournev is
G)
Fig. 9-1 R6glage retour automatique de
9, 2 R EG LAG E L 'E LE VA T I O N BR AS DE DU
Le bout de I'aiguille doit se trouver d une hauteur de 8 t 3mm au-dessus disque(Fig.9-2). du 9.3 REGLAGE DU MOTEUR 1. Brancher le courant et faire tourner la platine. 2. R6gler VR1 et VR2 dans l'ensemble du moteur pour que le stroboscope paraisse stationnaire. De nouveau, ce r6glage se fait par dessous. 3. Le r6glage de 45 tpm se fait sur VR1; le 16glage de 33 tpm se fait sur VR2. 4. Toujours r6gler sur 33 tpm.
Fig.9-2
R6glage la hauteurdu brasde pick-up de
Fig. 9-3
R6glage moteur du
12
|
|
|
> |
|