|
|
|
Who's Online
There currently are 5945 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
have download a number of manuals todate , most are excellant, one or two sometimes a little difficult to read but a least avaialable, great site .
Brad.
;
Excellent had everything I wanted, very happy with purchase
 ;
This service is relatively cheap, document is fast available, schematic is readable.
Thanks.
;
So far I´m a satisfied customer. I have only downloaded "TECHNICS SX-KN470 Service Manual" maybe I will use it later.
Best regards
Peter
;
Good manual. It is complete and of high quality, both text and graphics. The schematics are with the original big size, so it can be viewed or printed without any loss of resulution and sharpness.
1
2
3
4
5.1.7 FLOWCHART OF FAILURE ANALYSIS FOR THE AUDIO SYSTEM
Flowchart of Failure Analysis for The Audio System
A
No audio from monitor out
� MONI_A
The sound is not emitted audio out. Yes Is a signal output from IC4701? (pin 33, 34) 30 Yes No Check the surrounding of IC4701 and each input signal. If there was no ploblem, replace the MAIN ASSY. Check the communication between IC4701 and CN4005. NG Replace the MAIN Assy.
Has the signal arrived at CN4005? No
B
Yes Is a signal output from CN8803? Yes Has the signal come to TP8825 or TP8826? Yes No Check the contact between the CN8803 and R8886. Check the contact between the CN8803 and R8887. Check the communication between the CN8803 and Jack. If there was no ploblem, replace IO Assy. NG Replace the TANSHI Assy. No Check the Flexible cable between CN4005 and CN8803. NG Replace or reconnect flexible cable.
Input signal: 1kHz Sound volume is fixed to 25.
Waveforms
30
IC4701mV/div H: 400 µsec/div V: 500 - pin 33, 34 (AC)
Is a signal output from jack? Yes
No
NG
Replace the TANSHI Assy.
C
Finishing troubleshooting.
No audio output from subwoofer
� SUB-W
Has the sound been emitted from the Subwoofer? Yes
No
Cansel muting then check again. Yes Is the volume set to 0?
No
Cansel muting then check again.
No
Raise the volume then check again.
D
Is a signal output from IC4701? (pin 31, 32) Yes Is a signal output from IC4704? (pin 1, 7) Yes
No
31
No
Check the around of IC4701 and each input signal. If there was no ploblem, replace the MAIN ASSY. Check around IC4704. NG Replace the MAIN Assy.
32
No Check the communication between NG IC4704 to CN4005. Replace the MAIN Assy.
Has the signal arrived at CN4005? Yes Is a signal output from CN8803? Yes
No
Check the Flexible cable between CN4005 and CN8803. Check the contact between the CN8803 and R8892.
NG
Replace or reconnect flexible cable.
E
Has the signal come to TP8843? Yes Check the around of pin Jack.
No
NG Replace the TANSHI Assy.
Waveforms
Input signal: 100 Hz Sound volume is fixed to 25.
31
IC4701 -mV/div 32 (AC-SUBWOO) V: 200 pin 31, H: 4 msec/div
31
IC4701 - pin 31, 10 (DC-SUBWOO) V: 1 V/div H: 32 msec/div
32
IC4704 -mV/div (AC-SUBWOO) V: 200 pin 1, 7 H: 4 msec/div
32
IC4704 -mV/div (DC-SUBWOO) V: 500 pin 1, 7 H: 4 msec/div
F
98
1 2
PDP-607XD
3 4
|
|
|
> |
|
