|
|
|
Who's Online
There currently are 5616 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This schema available for me in good condition. I would highly recommend.
;
Thanks for this "hard to find" service manual.
I apreciate the good quality of scanning and the pages scanned in A3 format.
;
Helpd me mont a new carradio when prewius mont was a mess.
;
Very good service and quick service, very good quality of service manual!
;
Great tape deck manual!
I'm very positively surprised, because it is a very long manual, lot of pages, drawings, diagrams, description of how to make the alignment and adjustment procedures.
It is as good as the old "Naka" manuals from the 1970's - if somebody have seen them, they know what I mean by that.
I recommend to buy this very much !
1
2
3
4
A
8. ETC.
1 1 5 10 15 20 25 30 32
P AN E L
FAC T .
I N 1 � 5 0 6 0 2 � RGB � EHS 6 [ TBL 1 / 6 0 VS ]
7 Key operation
<DOWN> <UP> <SEL> <SET> : Shifting to MASK SETUP (+) : Shifting to PANEL REVISE (+) : MASK ON/OFF : Shifting to the next nested layer
5
10
B
15 16
E TC .
(+)
1 1
5
10
15
20
25
30
32
7 Key operation
<DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment value <LEFT> : Subtracting by one from the adjustment value <SET> : Determining the setting value and shifting to the upper layer <SEL> : MASK ON/OFF
P AN E L E TC .
FAC T .
I N 1 � 5 0 6 0 2 � RGB � EHS 6 [ TBL 1 / 6 0 VS ]
5
C
10
15 16
B AC K U P
E E P R OM
<=>
: NO
OPRT
D
<Lower-layer items of ETC.> No. Items Adjustment/Setting Value Remarks
"ERR" is indicated when no data are in the backup EEPROM. To activate the option to select TRANSFER, press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
1
BACKUP DATA <=>
<=>NO OPRT<=>TRANSFER<=>
2
E
DIGITAL EEPROM <=> <=>NO OPRT<=>REPAIR/DELETE<=>
"DELETE" is indicated when the main unit has been already adjusted. To activate the option to select REPAIR/DELETE, press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
3 4 5 6 7
PD INFO. <=> SD INFO. <=> HR-MTR INFO. <=> PM/B1-B5 <=> P-COUNT INFO. <=>
<=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> To activate the option to select CLEAR, repeatedly press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
F
� "NO OPRT" is selected when this submode is entered (to avoid accidental misoperation). � When each item is set, the process starts then the unit shifts to the upper layer. (When NO OPRT is determined, the unit will shift to the upper layer without doing anything.) � When data are set to be backed up, if the digital EEPROM has not been adjusted, do the operation of LED pattern No. 7.
72
1 2
PDP-436PE
3 4
|
|
|
> |
|
