|
Who's Online
There currently are 5570 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
TO PLAY ONLY DESIRED TRACKS/DISCS
Direct Program:
During normal playback or Magazine Hi-Lite Scan playback, the track being played can be programmed.
To erase a program (PD-M427 only) :
During program mode, press the CLEAR button on the remote control unit. The last program step is erased and the contents of the previous program step are displayed.
1. Press the PROGRAM button to enter the program mode. 2. To search for a desired track during normal play back, it is possible to skip to succeeding tracks by pressing the 4 1 or ¡ ¢ button.
Also, Magazine Hi-Lite Scan function can be used to move from track to track through the disc.
NOTE: Contents of a program can be erased during playback as well. However tracks preceding the currently playing track cannot be erased in this way.
3. If you wish to program the track currently playing, press the PROGRAM button while the track is playing.
÷ Direct programming is not possible during program playback.
To clear all of the program contents:
A. During stop mode, press the 7 button. B. When the magazine is ejected, the program contents will be cleared.
To check the program contents (PD-M427 only) :
During program mode, set the player to stop mode and press the CHECK button on the remote control unit. The program contents will be displayed in the programmed order. ÷ After confirming the last program step, the display will show �0-00�.
To modify the program contents (PD-M427 only) : 1. During program mode, set the player to stop mode and press the CHECK button on the remote control unit so that the program step to be corrected appears on the display. 2. Enter the new disc number with the DISC NUMBER (DISC 1-DISC 6) buttons and then press the 4 1 or ¡ ¢ button so that the new track number appears on the display. 3. Press the PROGRAM button.
÷ Repeat steps 1 through 3 to change other tracks as desired. ÷ If the 4 1 or ¡ ¢ button is not pressed within 2 seconds when correcting the track number, the displayed track number is automatically memorized.
PROGRAMMING A PAUSE (PD-M427 only)
Inserting a pause in your program can be very useful when carrying out recording. Press the 8 button on the remote control unit instead of entering a track number. �PA� appears on the display panel. ÷ For example, when recording on both sides of a cassette tape, if you program a pause after the last track to be recorded on the first side, program playback will pause at that point to allow you to switch tape sides. To resume program playback after the player enters pause mode, press the 8 button on the remote control unit or 6 button on the front panel.
NOTES: ÷ A pause can be programmed only when the program procedure is performed under stop mode. ÷ A pause cannot be programmed at the beginning of a program (P�01), nor can two pauses be programmed one after the other ÷ A pause inserted in a program is counted as one step. ÷ If a pause is programmed as the last step of a program, the player will not enter the pause mode.
12
En
|
|
|
> |
|