|
Who's Online
There currently are 5678 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
;
Easy and secure way to get a complete service manual of a vintage hifi component. Only some parts of the print copy are dificult to read. Nice price!
;
The manual is an excellent reproduction with complete schematics, made troubleshooting and repair a simple process.
;
Up to now you are the BEST! Prompt-efficient and so reasonable ! I have been after SONY service manual for quite some time !Thank you very much ! I can recomend your service to
all my collegagues ! V.Bergfield .
;
This is a very good quality print (scan) of the original SONY service manual. The original from Sony is on very thin paper. Nevertheless it is very clear and sharp and excellent readable. I'm very satisfied to have now this rare document. I've looking for it many years (infrequent). It contains very detailed circuit diagrams, exploded views, part lists, PCB view with good readable connection lines. Very recommended.
CONNECTING THE SPEAKER WIRES
(1) GM-X422/X1R/UC, GM-X322/X1R/UC (2) GM-X422/X1R/ES
two-chanThree-channel mode, two-way system The speaker output mode can be two-channel (stereo), one-channel (mono). nel (stereo), one-channel (mono), or threeTo connect speaker leads to suit mode. Connect the speakers channel (stereo + mono). To connect according to figures on the following pages.
� When connecting to speaker input, do not connect the RCA output. speaker leads to suit mode. Connect the � When connecting to RCA input, do not connect the speaker input. speakers according to figures on the folMid-high (Left) � When connecting to the speaker input, do not Speaker input
C1 Mid-high (Right)
lowing pages. C1 Two-channel (stereo) One-channel mode (mono)
(Right) � When connecting to the RCA input, do not L1 connect the speaker input. (Left)
connect the RCA output.
Woofer (Mono)
Two-channel mode (stereo)
Three-channel mode, three-way system
C1 (Left) Speaker (Mono) (Left)
(Right) Fig. 20 Speaker input (Left) High/mid-high Speaker (Right) Mid/mid-bass
L2 C2
(Left)
L1
22 Fig. 23 (Left) Woofer/sub-woofer
Speaker (Mono) (Right)
Fig. 18 (Right)
High/mid-high (3) GM-X422/X1R/EW One-channel mode (mono) (Right)
Mid/mid-bass L2 C2
(Right) The speaker output mode can be two-channel (stereo), one-channel Fig. 21 Speaker input (mono). To connect speaker leads to suit mode. Connect the speak� The inductor (L1 or L2 in the diagram) (Left) ers according to figures on the following pages.
acts as a low-pass filter. The capacitor (C1 or C2 in the diagram) acts as a highpass filter. The inductor (L) shall be used Two-channel (stereo) One-channel mode (mono) on the woofer/sub-woofer, and that a capacitor (C) shall be used on the high/mid-high.
Speaker (Mono)
Speaker (Mono) � Remember when bridging an amplifier it
Three-channel mode (stereo + Speaker speakers that have ratings of 4 ohms or mono)
lower impedance ratings it may cause channel/one-channel bridgeable amplifier, damage to the amplifier. but three channels can be achieved by combining the stereo and mono modes connected to the speaker wires, secure or using inductors and capacitors. solder them so they cannot be pulled loose. Tape or use heat shrink on the joints to prevent short circuits.
will see only half of the original speaker Fig. 19 impedance. Therefore, you must use (Left) higher. If you use speakers that have
(Right)
The power amplifier is basically a two-
GM-X422, GM-X322
24 Fig. 25
� When the inductors and capacitors are
19
|
|
|
> |
|