|
Who's Online
There currently are 5721 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Quality scan, great manual. I solved my problem with this manual.
;
The AKAI 1720 model reel to reel tape recorder described in this Manual is quite an old unit - circa late 1960's. As a consequence, the description of the mechanical details - and adjustments thereof - is quite critical. The manual does this quite well. The schematics are also well presented and have detailed PCB overlays. Probably the only negative is that some half-tone detail has been lost from the original manual as it has been scanned in simple B&W.
;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
;
This was the Sony CCU-500A Service manual I was looking for.
The price was reasonable.
The permission to download was quck.
I will use Owner-Manual.com for all my manual needs.
GM-X922, GM-X1022
22
Three-channel mode, two-way system Connecting the Speaker
wires Output Terminals
The speaker output mode can be two-chan-
1. Expose end of the speaker wires Mid-high (Left) nel (stereo), one-channel (mono), or threeC1
speaker leads suit the mode according to nippers or a cutter. figures on the following pages.
Twist � When connecting to the speaker input, do not connect the RCA output. C1 Mid-high (Right) � When connecting to the RCA input, do not
by about 10 mm and twist using channel (stereo + mono). Connect the
L1 Woofer (Mono)
10 mm connect the speaker input.
Fig.
Two-channel mode (stereo) Three-channel mode, three-way system 2. Attach lugs to speaker wire ends.
Fig. 22 16
Lugs not supplied. High/mid-high
L2 C2
� Use pliers, etc., crimp lugs to wires. C1 (Left) (Left) Woofer/sub-woofer wire Speaker (Mono) (Right)
Lug Mid/mid-bass (Left)
L1
Fig. 17 C2 Mid/mid-bass L2 Fig. 20 (Right)
3. Connect speaker wires to the
High/mid-high
speaker output terminals. (Right) Fig. 23 � Fix speaker wires securely with the termi� Inductors (L1 and L2 in the diagrams) � After pass through the terminal cover, conact as low-pass filters. Capacitors (C1 nect the terminal and C2 in the diagrams) act as high-pass woofer/sub-woofer, and capacitors (C)
Speaker (Mono) are used for the high/mid-high.
One-channel mode (mono)
nal screws.
Terminal screw filters. Inductors (L) are used for the
� Remember when bridging an amplifier it will see only half of the original speaker Terminal cover Fig. 21
wire Speaker impedance. Therefore, you must use
output speakers that have ratings of 4 ohms or terminal higher. If you use speakers that have
Three-channel mode (stereo + mono) damage to the amplifier.
lower impedance ratings it may cause
4. Cover the terminals. but three channels can be achieved by solder them so they cannot be pulled
Fig. 18 channel/one-channel bridgeable amplifier, connected to the speaker wires, secure or
The power amplifier is basically a two� When the inductors and capacitors are
combining the stereo and mono modes loose. Tape or use heat shrink on the using inductors and capacitors. joints to prevent short circuits.
Fig. 19
|
|
|
> |
|