|
Who's Online
There currently are 6012 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
5
6
7
8
1.3.5 RF level auto-adjustment (RFAGC)
This adjustment minimizes the dispersion of the RF level (RFO), which may be caused by disc-related errors, for more stable signal transmission by changing the amp gain between RFI and RFO. <Adjusting procedures> 1) The microcomputer sends the command to the servo LSI to read out the output from the RF level detecting circuit inside the servo LSI. 2) The microcomputer calculates the appropriate amp gain by using the output read out to adjust the RFO level at the prescribed one. 3) The microcomputer sends the command to the servo LSI to adjust the amp gain into the calculated one. This adjustment is automatically performed when: 1) During the setting-up mode, only the focus close operation ends. 2) Immediately before the setting-up ends (or right before the play mode starts) 3) During the play mode, the focus loop is locked again after unlocked.
A
B
1.3.6 Preamplifier gain adjustment
In this adjustment, when the reflected beams from disc surface are extremely weak (ex. when the lens is dirty, and a CD-RW is loaded), the whole gain in the RFAMP block (FE, TE, and RF amplifiers) is increased by +6dB or +12dB. <Adjusting procedures> When the system senses that the reflected beams from disc surface are extremely weak during the setting-up mode, the whole RFAMP gain is increased by +6dB or +12dB. After the gain is changed, the setting-up mode is restarted. If the whole RFAMP gain is always increased to the +6dB level in the play mode, the +6dB level will be employed at the starting of the setting-up mode from the next playback.
Gain of entire RFAMP Play the CD-RW with the gain being set to +12dB + 12dB D
C
+ 6dB
yy y ;;
Play is started with +6dB judging the lens is stained E Play at +6dB increases due to stained lens or other reasons (the typical gain is employed for the initial setup) Time F
TYP
Fig.1.3.1 Pre-amp gain adjustment
CX-3057
15 7 8
5
6
|
|
|
> |
|