|
|
|
Who's Online
There currently are 5900 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
EFFECT FUNCTIONS
PRODUCING BEAT EFFECTS
Display example Effect Name: DELAY
1234
4 BEAT 2, 3 TAP 1 AUTO
AUTO TAP
ABM
MIDI BPM % mS
Effect Channel Select: CH 1 BPM value: 120 BPM Parameter 1: 500 ms Beat multiple: 1/1
2 3 TIME LEVEL/DEPTH 5 ON/OFF
Beat effects allow the instant setting of effect times in synch with the BPM (beats per minute), thus allowing the production of a wide variety of effects in synch with the current rhythm, even during live performances.
4
1
Set BPM measuring mode to AUTO to measure BPM (beats per minute). The BPM of the input music signal is detected automatically. Whenever power is first turned ON, the function defaults to the [AUTO] mode. � In the event the track�s BPM cannot be detected automatically, the display�s BPM counter will flash. � Measurable range: BPM=70 to 180. It may not be possible to measure some tracks accurately. In this case, press the TAP button and input the beat manually.
Press the BEAT button ( , ) to select the beat multiple to which the effect is to be synchronized. � When is pressed, the beat count calculated from the BPM is doubled, and when is pressed, the beat count calculated from the BPM is halved (some effects also allow �3/4� setting). � The multiple of the selected beat (parameter 1 position) is displayed in seven sections on the display (see P. 12).
� The effect time corresponding to the beat�s multiple is set automatically. Example: When BPM = 120 1/1 = 500 ms 1/2 = 250 ms 2/1 = 1 000 ms Set the ON/OFF button to ON to enable the effect. � Each time the button is pressed, the effect alternates ON/ OFF (whenever power is first turned ON, the function defaults to OFF). � The ON/OFF button flashes when the effect is ON.
5
[Using the TAP Button for Manual BPM Input]
If the TAP button is tapped two times or more in synch with beat (1/4 notes), the BPM will be recorded as the average value recorded during that interval. � When BPM mode is set to [AUTO], tapping the TAP button will cause the BPM mode to change to the TAP mode, and the interval at which the TAP button is pressed will be measured. � When the BPM is set via the TAP button, the beat multiple becomes �1/1� (or �4/1�, depending on the effect selected), and the time for 1 beat (1/4 notes) or 4 beats will be set as the effect time. � If the TIME dial is rotated while depressing the TAP button, direct BPM can be set manually. If the TIME dial is rotated while holding the TAP button and AUTO buttons depressed, the BPM can be set in 0.1 units. Set the effect selector to the desired effect. � The display will show the name of the selected effect. � See P. 16 to 17 for details regarding the various effects. Set the effect channel selector to the channel you wish to apply the effect to. � The selected channel lights in the display�s channel name area. � If [MIC] is selected, the effect will be applied to both microphone 1 and microphone 2.
Parameter 1
Rotating the TIME (PARAMETER 1) dial adjusts the temporal parameter (time) for the selected effect. (With some effects, this is used for adjustments other than time parameters.) See P. 20 for details regarding the effect on parameter 1 of rotating the TIME (PARAMETER 1) dial.
Parameter 2
Rotating the LEVEL/DEPTH (PARAMETER 2) dial adjusts the quantitative parameter for the selected effect. See P. 20 for details regarding the effect on parameter 2 of rotating the LEVEL/DEPTH (PARAMETER 2) dial.
2
3
18
En
|
|
|
> |
|
