|
|
|
Who's Online
There currently are 5989 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
Section
02
Operating this unit
3 Push MULTI-CONTROL up or down to select the desired Q factor. Each time MULTI-CONTROL is pushed up or down, Q factor is selected in the following order: 2N�1N�1W�2W
Note If you make adjustments, CUSTOM curve is updated.
3 Push MULTI-CONTROL left or right to select the phase of subwoofer output. Push MULTI-CONTROL left to select reverse phase and REVERSE appears in the display. Push MULTI-CONTROL right to select normal phase and NORMAL appears in the display.
Adjusting subwoofer settings
When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Use MULTI-CONTROL to select SUB W2.
# When the subwoofer output is on, you can select SUB W2.
Adjusting loudness
Loudness compensates for deficiencies in the low- and high-sound ranges at low volume. 1 Use MULTI-CONTROL to select LOUDNESS. 2 Press MULTI-CONTROL to turn loudness on. Loudness level (e.g., MID) appears in the display.
# To turn loudness off, press MULTI-CONTROL again.
2 Push MULTI-CONTROL left or right to select cut-off frequency. Each time MULTI-CONTROL is pushed left or right, cut-off frequencies are selected in the following order: 50Hz�63Hz�80Hz�100Hz�125Hz Only frequencies lower than those in the selected range are outputted from the subwoofer. 3 Push MULTI-CONTROL up or down to adjust the output level of the subwoofer. Each time MULTI-CONTROL is pushed up or down, subwoofer level increases or decreases. +6 to �24 is displayed as the level is increased or decreased.
3 Push MULTI-CONTROL left or right to select a desired level. Each time MULTI-CONTROL is pushed left or right, level is selected in the following order: LOW (low)�MID (mid)�HIGH (high)
Using subwoofer output
This unit is equipped with a subwoofer output which can be turned on or off. 1 Use MULTI-CONTROL to select SUB W1.
Using the high pass filter
When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are outputted from the front or rear speakers. 1 Use MULTI-CONTROL to select HPF.
2 Press MULTI-CONTROL to turn subwoofer output on. NORMAL appears in the display. Subwoofer output is now on.
# To turn subwoofer output off, press MULTI-CONTROL again.
2 Press MULTI-CONTROL to turn high pass filter on. 80Hz appears in the display. High pass filter is now on.
36
En
|
|
|
> |
|
