|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great manual, great price. Has a few of the basic operating instructions that most service manuals leave out. Complete instructions for disassembling board by board, safety precautions, schematics, complete parts list.
;
I am very pleased with the service manual for my RT-909. This was an easy purchase and great procuct, and much cheaper than other venues i had looked at. This web site is now listed in my favorites list. KEEP UP THE GOOD WORK. THANKS. J. BROWN
;
A very well written and easy to understand manual.
;
There was no problem at all.After paying i had to wait only a few hours,than i could
download the manual in best pdf-quality.
Thank You !
 ;
I found this service manual to be complete in every detail except for troubleshooting charts. It would be helpful if it had a set of troubleshooting charts; however it is a very good manual otherwise and for the price it is very well worth it.
CDX-P2050VC,P2050VN,P2050VS
7. GENERAL INFORMATION
7.1 DIAGNOSIS 7.1.1 TEST MODE
- CD Test Mode
1) Precautions � This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is connected to REFO(approx. 2.5V) instead of GND. If REFO and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the following. Do not connect the negative probe of the measuring equipment to REFO and GND together. It is especially important not to connect the channel 1 negative probe of the oscilloscope to REFO with the channel 2 negative probe connected to GND. Since the frame of the measuring instrument is usually at the same potential as the negative probe, change the frame of the measuring instrument to floating status. If by accident REFO comes in contact with GND, immediately switch the regulator or power OFF. � Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring required for measurements. � Before proceeding to further adjustments and measurements after switching regulator ON, let the player run for about one minute to allow the circuits to stabilize. � Since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the system when making adjustment. � Disc detection during tray extraction and return operations is performed by means of the photo transistor in this unit. Consequently, if the inside of the unit is exposed to a strong light source with the outer casing removed for repairs or adjustment, the following malfunctions may occur: *Even with a disc loaded, the unit detects "no disc" and cannot start play. *Although a 12-cm disc is loaded, the unit detects "8cm disc" mistakenly. When the unit malfunctions this way, either re-position the light source, move the unit or cover the photo transistor. � During exchanging discs, do not press the keys for the discs to be exchanged. 2) Test Mode This mode is used for adjusting the CD mechanism module of the device. � Test mode starting procedure Reset while pressing the 4 and 6 keys together. � Test mode cancellation Switch ACC, back-up OFF. � If the 8 or 9 key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to the lens stuck). � Jump operation of TRs other than 100TR continues after releasing the key. CRG move and 100TR jump operations are brought into the �Tracking close� status when the key is released. � Powering Off/On resets the jump mode to �Single TR (91)�, the RF AMP gain setting to 0 dB, and the automatic adjustment value to the initial value. � During exchanging discs, do not press the keys for the discs to be exchanged.
Key to adjustment text inside (12 keys type) BAND TRK+/FF TRK-/REV 7 8 9 10 11 12 DISCSOURCE ON/OFF
HEAD UNIT (6 keys type) BAND TRK+/FF TRK-/REV 1 2 3 4 5 6 DISCSOURCE ON/OFF
45
|
|
|
> |
|
