There are currently no product reviews.
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
;
Manual was complete and available promptly, since I had lost my original manual. Very good response.
;
Whilst this is a photo copy, and some of the pages are a little askew, it was all readable and intact. A real bonus finding an old manual for a classic piece of kit that no other site had.
Great stuff.
The output video resolution depends on the video output terminal. See the table below. The table below shows the output video resolution for the different terminals when the frame/field frequency of the playback source is 50 Hz on the upper line, the resolutions when the source's frame/ field frequency is 60 Hz on the lower line.
Output video resolution setting Auto2 576i or 480i 576p or 480p 1080i HDMI OUT terminal COMPONENT S-VIDEO/ VIDEO VIDEO output terminals1 Resolution � preferred by TV3,4 576/50i 480/60i 576/50p 1080/50i 1080/60i 1080p2 1080/50p7 1080/60p7 Source Direct Resolution recorded on disc3,8,9 Resolution recorded on disc8,9,10 576/50i 480/60i 480/60p 576/50i 480/60i 576/50p 576/50p 480/60p 1080/60i6 � output terminal1 � 576/50i 480/60i 576/50i 576/50i 480/60i 480/60i � PAL �5 PAL �5 PAL PAL �5 PAL �5 PAL �5 �
5
the TV system format for the video signal output from the S-VIDEO and VIDEO output terminals is set to NTSC on PAL TV. When playback is stopped, the frame/field frequency and TV system settings remain at the settings last used. The frame/field frequency and TV system settings do not change even when the power is turned off. They only switch when a video material with a different frame/field frequency is played. If the picture is not displayed on the TV when a source with a different frame/field frequency is played, use the procedure below to switch the frame/field frequency and TV system settings for the signal output from the player. Eject the disc, then press the � OPEN/CLOSE button on the front panel while pressing the � button to switch to a different frame/field frequency. The frame/field frequency switches between 50 Hz and 60 Hz each time this operation is performed. The indicator for the frame frequency�s current setting lights on the front panel display (page 13).
03
TV system
� About Film material
The film material is a video signal with a frame rate of 24 frames/ second. For example, these materials include 1080/24p, 720/24p, etc.
Example: Video resolution of the currently playing disc
Output Video Resolution Auto
Source : 1080/24p Current Output : 1080/24p
1. Depending on the BD, the pictures may not be output. 2. Cannot be selected when the video signals are being output from the COMPONENT VIDEO output terminals, S-VIDEO output terminal or the VIDEO output terminal. 3. For details on the output of film material (1080/24p or 720/24p video signals), see To output film material. 4. Sources with a resolution of 720/50p, 720/60p and 720/24p are output at 1080/ 50i or 1080/60i, even if the TV�s preferred resolution is 1080/50p or 1080/60p. 5. Depends on the NTSC on PAL TV setting (page 41). 6. DVD-Video or DVD VR format is output at 480/60p. BDs format may be output at 480/60p. 7. Depending on the connected HDMI cable, the video signals may not be output. Also, sources with a resolution of 720/50p is output at 1080/50i, and 720/60p and 720/24p are output at 1080/60i. 8. Depending on the connected TV, the video signals may not be output. 9. 720/24p film material is output at 720/60p. 10. 1080/24p film material is output at 1080/60i.
Output video resolution from the player
� To output film material
To output 1080/24p film material from the HDMI output terminal, set the output video resolution to either Auto or Source Direct. Caution � 1080/24p signals can only be output from the HDMI OUT terminal. They cannot be output from other video terminals. � When Auto is selected, the picture is output at 60 frames/ second if your TV is not compatible with 1080/24p signals. � When Source Direct is selected, the signals are output as such, even if your TV is not compatible with 1080/24p signals. If the picture is not displayed properly, use OUTPUT RESOLUTION to set to the output video resolution at which the picture is properly displayed. � 720/24p video signals are output at 60 frames/second, even if the resolution is set to Auto or Source Direct.
Caution � On some TVs, the picture may not be displayed properly when the resolution is switched. If this happens, use OUTPUT RESOLUTION to set to a resolution at which the picture is properly displayed. � When video signals are being output with a resolution of 1080/ 50i, 1080/50p, 720/50p, 1080/24p, 1080/60i, 1080/60p or 720/60p from the HDMI output terminal or component video output terminals, the picture may be output with an aspect ratio of 16:9, even if the TV Aspect Ratio is set to 4:3 (Standard). � The picture may not be displayed for a while when the resolution is switched.
� About the frame/field frequency and NTSC/ PAL TV systems
By factory default setting, the frame/field frequency is set for an output of 50 Hz, and the video signal output from the S-VIDEO and VIDEO output terminals is set to be output in the PAL TV system format. When sources with a frame/field frequency of 60 Hz or 24 Hz are played, the output frame/field frequency automatically switches to 60 Hz (or 24 Hz for HDMI, depending on the setting), and
25
En
