|
Who's Online
There currently are 5812 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Très satisfait ! envoi rapide, Grand catalogue disponible. Many thanks !
;
Delivery came quite promptly and in a very readable format. Thank you.
;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
07
Surround sound settings
Using the Virtual Surround Back mode
This mode allows you to hear a virtual surround back channel through your surround speakers. You can choose to listen to sources with no surround back channel information, or if the material sounds better in the format (for example, 5.1) for which it was originally encoded, you can have the receiver only apply this effect to 6.1 encoded sources like Dolby Digital EX or DTS-ES.1
Adjusting the channel levels using the test tone
If you prefer, you can set the channel levels using a test tone as a reference, rather than playing a source (see Channel level setting on page 30). A test tone is played through each speaker in turn, allowing you to adjust the level as it plays. You can also adjust the channel levels for surround sound using test tone.
ENTER
1
SETUP
Open the �Sound Setup� menu. 1 TONE Carry out tone testing. The test tone is output from each speaker in turn. Select �Virtual SB�, then press ENTER. Adjust the volume level below 50.
TEST
ENTER
2
3 Select a setting. Select one of the following: � Vir.SB On � Virtual Surround Back is always used (for example, on 5.1 encoded material) � Vir.SB Auto � Virtual Surround Back is automatically applied to 6.1 encoded sources (for example, Dolby Digital EX or DTS-ES), DTS Neo:6 or Advanced Surround mode � Vir.SB Off � Virtual Surround Back mode is switched off 4
ENTER
2 Adjust the channel level of a tune while it is playing. The aim is to adjust the levels so that you hear the test tone at the same volume from each speaker. You can adjust the level of each channel by ±10 dB. � You can adjust the overall volume of test tone output using the VOL +/� buttons (this does not affect the channel level settings). � Because of the ultra low frequencies the subwoofer produces, it may sound quieter than it really is. We suggest adjusting the subwoofer level while listening to a source. See the method described in Channel level setting on page 30. 3
ENTER
Press to exit.
LFE Attenuate
Some Dolby Digital and DTS audio sources include ultralow bass tones. Set the LFE attenuator as necessary to prevent the ultralow bass tones from distorting the sound from the speakers. The LFE is not limited when set to 0dB, which is the recommended value. When set to -5dB, -10dB, -15dB or -20dB, the LFE is limited by the respective degree. When Off is selected, no sound is output from the LFE channel.
ENTER
Press to exit test tone setup once you have
finished. � If you use the Auto MCACC feature again, it will overwrite the settings you have made here.
1
SETUP
Open the �Sound Setup� menu.
ENTER
2
ENTER
Select �LFE ATT�, then press ENTER.
3 confirm.
Adjust the setting then press ENTER to
Note 1 Depending on the input signal and the listening mode, the Virtual Surround Back mode may not be effective.
32
En
|
|
|
> |
|